Opens side-to-side.
Mounted across the truck, every DartSolar slides out past both sides. One or two on the cab rack, two more on the truck bed.
FrontSeen from aboveRear
- 24 inchesof rack length for each DartSolar. Mounted across the truck, four fit on one pickup.
- About 4 feetpast each side of the truck when open. No poles, no guy lines.
- 10 secondsto slide one open or closed, with two fingers.
Start today.
From $1,350, or $113/mo.* Free delivery.
From the cab alone, or the cab and the bed.

1,000watts
Two on the cab, front to back.
Mount two DartSolars side by side on the cab rack. Open, the front panels reach over the windshield and hood, and the rear panels reach back over the bed.
- No bed rack needed
- The bed stays completely free
- The bed sits in shade under the rear panels

1,500 to 2,000watts
Across the cab and the bed rack.
Mount the DartSolars across the truck and expand them side-to-side. One or two fit the cab rack, and two more ride on a low rack over a 5 to 6.5 foot bed.
- Any bed rack with crossbars works
- The bed stays open for gear underneath
- No tall framing over the bed needed
What people are saying
Four newsrooms on DartSolar.
DartSolar isn’t just about innovation; it’s about practicality.
DartSolar ... soaks up the maximum amount of sunlight.
…the company’s midlevel, 1,000-watt system could add 10 to 20 miles of range to a parked Tesla...
...the solar roof rack can add a useful amount of range..
The bed stays open.
The DartSolars on the truck bed ride on a low rack, just above the bed. Drop the tailgate and everything you haul still loads underneath.
- Any bed rack with crossbars works
- No tall framing over the bed needed
- Closed, each DartSolar is 3 inches tall and 45 pounds
Rooftop solar for camping, overlanding
and off-grid living. And for blackouts.
Each solar panel
A tenth of an inch thick.
A DartSolar is three of these panels, one on top of the other. Each 170-watt panel is about 0.1 inch (2.5 mm) thick, 54 × 23 inches, and built in layers.
- ETFE coatingThe outer surface of the sheet.
- Half-cut 182 mm solar cells170 watts and 30 volts per panel.
- PETPart of the panel sheet.
- Fiberglass backingThe stiff layer behind the cells.
Layer order shown for illustration.
Three reasons to get a DartSolar.
Only 1.5 inches face the wind
Only 1.5 inches (3.8 cm) at the front displaces the wind, so drag loss is minimal.
It is 100 mph and 10k fatigue tested
Tested at 100 mph (160 km/h) and road track beaten. Please drive safely, below 70 mph.
It fits any vehicle with a roof rack
Any electric vehicle, SUV, pickup truck, van or RV. The only thing it needs is a roof rack.
Start with one. Add as you go.
Every DartSolar is the same 500-watt module, and they join into one array. Put one on the truck bed now and add more later.
How many DartSolars?
Two on the cab rack, two on the truck bed.
- 2,000wattsof solar
- ~12,000Whon a sunny day*
- 180lbon the racks
*One DartSolar made 3,000 watt-hours on a sunny August day in Los Angeles, multiplied by the number of DartSolars. Check your racks’ dynamic load rating against the weight.

1,000 watts
from the cab alone.
Two DartSolars side by side on the cab rack.
The bed stays completely free.
From $1,350, or $113/mo.* Free delivery.
Over-engineered
Strong where it counts.
Solar panelsETFE coated, fiberglass backed
Half-cut 182 mm cells.
100mph
160 km/h, road track beaten.
1/8inch aluminum
3 mm thick.
6061T6
Custom extruded aluminum.
Nylon, ASA and TPU
Injection molded and UV-protected.
4mm polycarbonate
0.157 inch thick. The material of race car windshields and jet cockpits, about 250 times more impact resistant than glass.
Water, hail and rock proof
Fully repairable.
Technical specifications.
Power
Solar panels
- 2 expand, 1 static
- Each: 170 watts, 30 volts, 54 × 23 in (137 × 58 cm), about 0.1 in (2.5 mm) thick
Dimensions, closed
Dimensions, open
Height that causes drag
Weight
Voltage
- 30 volts with the Parallel Adapter
- 90 volts with the Series Adapter
Panel build
- ETFE coated sheet
- 182 mm half-cut solar cells
- Fiberglass backing
- PET
Structure
- Aluminum frame, 1/8 in (3 mm) thick
- Protective shell of 4 mm (0.157 in) polycarbonate
- Telescopic tubes of custom extruded aluminum 6061 T6
- Injection molded, UV-protected Nylon, ASA and TPU plastics
Power unit
Five things worth knowing.
It expands to about 14 feet
Drive closed at 58 inches. Park, slide it open, and charge with all your solar panels.
It opens in ten seconds
Two fingers and ten seconds are all it takes to open a DartSolar. It slides open and closed easily.
Only 1.5 inches face the wind
Only 1.5 inches (3.8 cm) at the front displaces the wind, so drag loss is minimal.
It is tested at 100 mph
Tested at 100 mph (160 km/h). Road track beaten and 10k fatigue tested. DartSolar is strong.
It fits any vehicle with a roof rack
Any electric vehicle, pick-up truck, van or RV. Only a roof rack is required.
How much sun can you capture?
Solar calculator.
Pick your city or country, the month and what you drive. See the sunlight on the map and what DartSolar makes of it.
Sunlight in July
Results
Solar makes
~9.2kWh
on an average July day
Up to 9.8 kWh on a clear day
Power unit receives
~7.7kWh
after all losses
An EV stores
~5.4kWh
in its battery, after charging losses
~22 miles
estimated range for an EV that uses 250 Wh/mi
Estimates only, for an average day in the month you pick with the panels open all day. Energy is scaled from 3,000 Wh, measured with one DartSolar on a sunny August day in Los Angeles, using NASA POWER monthly sunlight averages (2001 to 2025) for your area. A country shows the average of its cities in our list. The power unit and EV figures use the shares from that test: of 6,000 Wh made, about 5,000 Wh reached the power unit and about 3,500 Wh reached the car’s battery. Range assumes an EV that uses 250 Wh/mi (155 Wh/km), whatever vehicle you pick. With the panels closed while driving, expect about one third. How many DartSolars fit depends on your roof and rack. Power unit not included. City list: GeoNames.
When your driveway is your power plant, you become more resilient. Storms, blackouts, fuel shortages: none of it touches you the same way.
From the DartSolar mission, by Omid, founder. Read it
The sun crosses the sky. The meter keeps counting.
Four DartSolars, two on the cab and two on a bed rack, each opening side-to-side. On a sunny August day in Los Angeles, one DartSolar made 3,000 watt‑hours. Four make about 12,000.
12,000watt‑hours so far
3,000 Wh measured with one DartSolar on a sunny August day in Los Angeles, multiplied by the number of DartSolars. The sun path and shadow are drawn for illustration.

Self-reliance
starts now.
Charges as you drive.
More when you park.
Closed, one panel of every DartSolar stays in the sun, so about a third of the array keeps charging on the road. Park, slide them open, and all of it goes to work.
Driving, closedParked, open side-to-side
About 650 watts charging2,000 watts charging
Shown: four DartSolars, two on the cab and two on the truck bed, a 2,000-watt pickup. The panel that stays on top keeps working while the other two are stowed.
Run the whole day
off the truck.
A 2,000-watt array runs a fridge, an induction cooktop, laptops and a fan all day, with a surplus banked for the night.
- ~12,000Whmade by 2,000 watts per day*
- ~10,000Whstored in your power unit per day*
*Estimates for a sunny summer day in Los Angeles with the panels expanded, based on DartSolar’s own tests. Cloudier places and winter days make less. Power unit not included.
- A fridgeRunning
- An induction cooktopRunning
- LaptopsRunning
- A fanRunning
Your awning makes electricity.
Expanded side-to-side, a DartSolar reaches about four feet past each side of the truck. That is a patch of shade the size of a campsite kitchen.
- No poles
- No guy lines
- No fabric to roll up
Fully expanded, a DartSolar is rated for gusts up to 25 mph. Two fingers close it when the wind picks up.
Take power anywhere.
From $1,350, or $113/mo.* Free delivery.
FrontSeen from aboveRear
The bed sits in shade.
With two DartSolars on the cab, opened front to back, the rear panels reach back over the bed. That makes it a better place to work out of on a July afternoon.
- 1,000 watts from the cab rack alone
- No bed rack
- No change to how you load the truck
Rig your truck.
From $1,350, or $113/mo.* Free delivery.
Wired for a low sun.
When the sun is low, the cab throws a shadow into the front of the bed. Mount the bed DartSolars toward the tailgate, where that shadow never reaches them, and they keep producing.
- Bed modules sit back, clear of the cab’s shadow
- 90-volt series for modules in full sun
- Every DartSolar ends in one XT60 plug
The checklist.
It opens in ten seconds
Two fingers and ten seconds are all it takes to open a DartSolar. It slides open and closed easily.
Only 1.5 inches face the wind
Only 1.5 inches (3.8 cm) at the front displaces the wind, so drag loss is minimal.
It is tested at 100 mph
Tested at 100 mph (160 km/h). Road track beaten and 10k fatigue tested. DartSolar is strong.
It fits any vehicle with a roof rack
Any electric vehicle, pick-up truck, van or RV. Only a roof rack is required.
Any power unit. Any country.
DartSolar is the world’s first solar roof rack for EVs that works with any power unit. It ends in one XT60 plug, the standard solar input on most of them.
One XT60 plug30 volts in parallel or 90 volts in series
Tokyo
100 volts
São Paulo
Dual voltage
Los Angeles
120 volts
Plug in and power up.See the best power units

Your truck,
off the grid.
More benefits
Charge all the time
The panels charge your power unit as you drive.
Power anywhere
Take your detachable power unit with you. You are not glued to your vehicle.
Modular
Join DartSolars to build 500 to 2000+ watt solar arrays.
Plug-and-play
Works with any power unit brand, including EcoFlow, Jackery and Bluetti.
Easy to install
Installation takes minutes at home. No need to drive to an installation site.
Cooler cabin
Cools the vehicle cabin by 15 degrees, offsetting air conditioning.
Repairable
Solar panels, plastic parts, wires, brackets and shell are all serviceable and repairable.
Open library
Download any .step file of the plastic parts to 3D print repairs and upgrades.
Side-to-side
Expands side-to-side for trucks, vans and recreational vehicles.
Print your own repairs.
Every plastic part of a DartSolar is open source. Print a repair at home or purchase a replacement part.
- 1Enter your email
- 2Accept the Open Hardware Agreement
- 3Download the .step files
Print in a UV-stable material such as ASA, with a 0.4 mm nozzle. Files with “shoe” in the name print in TPU. Printed parts are not covered by the Limited Warranty; the rest of your DartSolar still is.
Solar that rides.
From $1,350, or $113/mo.* Free delivery. Self-reliance starts now.

